eng Русский язык

Intertuf 262

A surface tolerant, two pack epoxy primer.

Intended uses

As an epoxy anticorrosive coating for use from Keel to Rail. Suitable for use with controlled cathodic protection. For use at Newbuilding, Maintenance & Repair or On Board Maintenance.

color KHA303-Red
Finish/Sheen Matt
Part B (Curing Agent) KHA062
Volume Solids 73% ±2% (ISO 3233:1998)
Mix Ratio 4.00 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness 125 microns dry (171 microns wet)
Theoretical Coverage 5.84 m2/litre at 125 microns dft, allow appropriate loss factors
Method of Application Airless Spray, Brush, Roller
Flash Point Part A 28°C; Part B 34°C; Mixed 29°C
Induction Period Not required

Drying Information

  Substrate Temperature
  5°C 10°C 25°C 35°C
Touch Dry [ISO 1517:73] 9 hrs 7 hrs 4 hrs 4 hrs
Hard Dry [ISO 9117:90]

47 hrs

29 hrs 9 hrs 5 hrs
Pot Life 8 hrs 7 hrs 4 hrs 2 hrs

Overcoating Data

Overcoated By Substrate Temperature
  5°C 10°C 25°C 35°C
  Min Max Min Max Min Max Min Max
Interbond 201 24 hrs 28 days 18 hrs 28 days 8 hrs 28 days 4 hrs 15 days
Interbond 501

24 hrs

21 days 18 hrs 21 days 6 hrs 21 days 4 hrs 21 days
Intergard 263 24 hrs 21 days 16 hrs 14 days 6 hrs 21 days 4 hrs 21 days
Intergard 282 24 hrs 14 days 16 hrs 21 days 6 hrs 14 days 4 hrs 14 days
Intergard 740 24 hrs 28 days 18 hrs 20 days 6 hrs 14 days 4 hrs 7 days
Intertuf 262 24 hrs 28 days 18 hrs 28 days 6 hrs 28 days 4 hrs 15 days


Overcoating information for all other Intergard, Intertuf, Interbond and Interprime products refer to Intertuf 262 above.

Regulatory data


279 g/lt as supplied (EPA Method 24) 229 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)


VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.


When used as part of an approved scheme, this material has the following certification:

  • Food Contact - Carriage of Grain (NOHA)
  • Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16))
  • Fire Resistance - MSC61(67) Smoke & Toxicity (WFR)
  • Fire Resistance - Marine Equipment Directive compliant
  • Food Contact - FDA Compliant: Dry Foodstuffs

Consult your International Paint representative for details.

System and compatibility

Consult your International Paint representative for the system best suited for the surfaces to be protected.

Surface preparations

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. Intertuf 262 can be applied over Intergard 269, when used as a holding primer to protect the blast. The primer surface should be dry and free from all contamination and Intertuf 262 must be applied within the overcoating interval specified (consult the Intergard 269 product data sheet).


Where necessary, remove weld spatter and smooth weld seams and sharp edges. Welds and damaged areas should be blast cleaned to Sa21⁄2 (ISO 8501-1:2007). For PVB and unapproved shop primers, the surface should be blast cleaned to Sa21⁄2 (ISO 8501-1:2007) or power tooled to Pt3 (JSRA SPSS:1984) Intact zinc silicate shop primers should be prepared by sweep blasting to International Paint standard AS2 or by power tooling to Pt3 (JSRA SPSS:1984). For iron oxide epoxy shop primers, ensure the intact primer is clean and dry.


Underwater Hull/Boottop/Topsides

Abrasive blast clean to Sa2 (ISO 8501-1:2007). If oxidation has occurred between blasting and application of Intertuf 262, the surface should be reblasted to the specified visual standard. Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner. Intertuf 262 may be applied to surfaces prepared to International Paint Hydroblasting Standard HB2 which have flash rusted to no worse than HB2M. Intertuf 262 may be applied using a wash/blast/wash surface preparation method: - High pressure (minimum 3000 psi) fresh water wash - Abrasive blast clean to Sa2 (ISO 8501-1:2007) - Carry out a second high pressure (minimum 3000 psi) fresh water wash - Residual salt level must be below 10μg/cm2 - Visual standard of flash rusting must correspond to no worse than HB2M


Consult International Paint. Consult your International Paint representative for specific recommendations.



Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.


Not recommended. Use International GTA220 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Recommended Tip Range 0.53-0.84 mm (21-33 thou) Total output fluid pressure at spray tip not less than 176 kg/cm2 (2500 p.s.i.)

Conventional Spray

Application by conventional spray is not recommended.


Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


International GTA220/GTA822

Work Stoppages and Cleanup

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA220/GTA822. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Clean all equipment immediately after use with International GTA220/GTA822. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.


In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."


All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.


A system of Intertuf 262 followed by Intergard 263 may be used for the spot repair or upgrade of the following substrates: Spot Repair (Suitable Substrates): - Epoxy, Coal Tar Epoxy, Chlorinated Rubber, Vinyl Tar, Tar-free Vinyl Substrates not suitable for repair : - Bituminous Upgrade (Suitable Substrates): - Epoxy, Coal Tar Epoxy, Chlorinated Rubber Substrates not suitable for upgrading:- Vinyl Tar, Tar-free Vinyl, Bituminous Feathered overlap areas must be kept to a minimum. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

Unit size

Unit size Part A Part B
  Vol Pack Vol Pack
20 lt 16 lt 20 lt 4 lt 5 lt

For availability of other unit sizes consult International Paint

Unit shipping weight

Unit size Unit Weight
20 lt 29.03 Kg


Shelf Life 12 months at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.