eng Русский язык
Версия для слабовидящих

Intersmooth 365 SPC

High performance, TBT free, self polishing copolymer (SPC) antifouling system with patented Copper Acrylate


Suitable for use on both Coastal and Deep sea vessels depending on activity profile and intended service life
For use at Newbuilding.

color BEA363-Dark Brown, BEA364-Dark Red, BEA365-Mid Brown, BEA373-Dark Brown, BEA374-Dark Red (Note: BEA373-Dark Brown, BEA374-Dark Red only available in China and specific locations in Europe only - see Worldwide Availability section)
Finish/Sheen Not applicable
Part B (Curing Agent) Not applicable
Volume Solids 40% ±2% (ISO 3233:1998)
Mix Ratio 4.5 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness Range: 70 - 140 microns dry (175 - 350 microns wet) may be specified depending upon end use.
Theoretical Coverage Range: 5.7 - 2.9 m²/litre at 70 - 140 microns dft, allow appropriate loss factors
Method of Application Airless Spray, Brush, Roller
Flash Point

Single Pack 22°C (Product produced and supplied in North America has a flashpoint of 21°C due to locally sourced solvents. There is no detrimental effect on product performance.)

Drying Information

  Substrate Temperature
  -5°C 5°C 25°C 35°C
Touch Dry [ISO 9117/3:2010] 120 mins 60 mins 40 mins 30 mins
Before Flooding 30 hrs 18 hrs 12 hrs 10 hrs

Overcoating Data

see limitations

Overcoated By Substrate Temperature
5°C 25°C 35°C
  Min Max Min Max Min Max Min Max
Intersmooth 360 SPC 12 hrs 6 mths 6 hrs 6 mths 4 hrs 6 mths 3 hrs 6 mths


Refer to your International Paint representative for minimum drying time before flooding at higher dry film thickness per coat.


VOC 518 g/lt as supplied (EPA Method 24) 343 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)


VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.


USA Federal EPA Registration No. 2693-188 (BEA363, BEA364) BEA365 is not approved in the USA This product is not registered in Canada. See Page 4 for additional Regulatory Data.

This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26).




When used as part of an approved scheme, this material has the following certification:
Product recognised by the following classification societies as compliant with the International Convention on the
Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001):
• Lloyds Register
• Germanischer Lloyd
• Korean Register of Shipping
• Det Norske Veritas
• Bureau Veritas
Consult your International Paint representative for details.


Consult your International Paint representative for the system best suited for the surfaces to be protected.


Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.


Intersmooth 365 SPC should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intersmooth 365 SPC must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO 8501-1:2007) and primed prior to the application of Intersmooth 365 SPC Consult your International Paint representative for specific recommendations.




This material is a one pack coating. Always mix thoroughly with a power agitator before application.


Not Recommended. Use International GTA007 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Tip Range 0.46-0.66 mm (18-26 thou)
Total output fluid pressure at spray tip not less than 211 kg/cm² (3000 p.s.i.)


Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


International GTA007

Work Stoppages and Cleanup

Thoroughly flush all equipment with GTA007. All unused material should be stored in tightly closed containers. Partially filled containers may show surface skinning and/or a viscosity increase of the material after storage. Material should be filtered prior to use.


In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."


All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.


Coating lifetime is directly proportional to thickness applied. Performance of the product is dependent upon the specified film thickness being achieved.
On immersion, Intersmooth 365 SPC will exhibit a slight colour change. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.


Refer to container label for information concerning Precautionary Statements, Directions for Use and Storage and Disposal.


Unit Size  
  Vol Pack
20 lt 20 lt 20 lt
5 US gal 5 US gal 5 US gal

For availability of other unit sizes consult International Paint


Unit Size Unit Weight
20 lt 34.18 Kg
5 US gal 71.5 lb


Shelf Life 6 months at all temperatures (BEA373 & BEA374). 18 months at all temperatures for all other versions. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.