eng Русский язык
Версия для слабовидящих

Intershield 852

A high build, spray applied, two pack epoxy medium texture non-skid finish. Intershield 852 is hard wearing with good chemical resistance.

Intended uses

As a non-skid flight deck coating, complying with DEF STAN 80-134 Type 1- Medium Texture. Intershield 852 can also be used on any other deck or walkway subject to heavy wear.

color ADA112-Extra Dk Sea Grey, ADA113-Dk Admiralty Grey
Finish/Sheen Not applicable
Part B (Curing Agent) ADA134
Volume Solids 75% ±2% (ISO 3233:1998)
Mix Ratio 4.66 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness 1000 microns dry (1333 microns wet)
Theoretical Coverage 0.75 m2/litre at 1000 microns dft, allow appropriate loss factors
Method of Application Conventional Spray, Roller
Flash Point Part A 23°C; Part B 101°C; Mixed 41°C
Induction Period Not applicable

Drying Information

  Substrate Temperature
  10°C 15°C 25°C 35°C
Touch Dry [ISO 1517:73] 8 hrs 7 hrs 5 hrs 2 hrs
Hard Dry [ISO 9117:90] 36 hrs 28 hrs 16 hrs 12 hrs
Pot Life 8 hrs 7 hrs 6 hrs 4 hrs

Overcoating Data

Overcoated By Substrate Temperature
  10°C 15°C 25°C 35°C
  Min Max Min Max Min Max Min Max
Intershield 852 36 hrs ext 26 hrs ext 12 hrs ext 8 hrs ext

Regulatory data

VOC

219 g/lt as supplied (EPA Method 24) 137 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)

Note.

VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.

DEF STAN

Complies with DEF STAN 80-134 Type 1- Medium Texture

CERTIFICATION

When used as part of an approved scheme, this material has the following certification:

  • Fire Resistance - MSC61(67) Smoke & Toxicity (WFR)
  • Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16))

Consult your International Paint representative for details.

System and compatibility

Consult your International Paint representative for the system best suited for the surfaces to be protected.

Surface preparations

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.

NEWBUILDING/MAJOR REFURBISHMENT

Intershield 852 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intershield 852 must be applied within the overcoating intervals specified (consult the relevant product data sheet). Areas of breakdown, damage etc. should be prepared to the specified standard (eg. Sa21⁄2 (ISO 8501-1:2007)) and primed prior to the application of Intershield 852. Consult your International Paint representative for specific recommendations.

APPLICATION

Apply by brush, roller or spray. Apply mixed material by brush, roller, or spray in an even coat to the properly prepared surface. Apply at 150 microns wet which will yield 125 microns dry film thickness. The recoat schedule must be adhered to. Surfaces must be abraded prior to applying additional coats if maximum recoat time has been exceeded. Consult the following equipment recommendations:

Mixing

Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.

Thinner

Not Recommended. Use International GTA007 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Not suitable.

Conventional Spray

Recommended. Use 10 or 20 litre pressure pot equipped with 2 metres of 12-15mm internal diameter feed hose, gun nozzle size 10mm, or hopper gun for small areas.

Brush

Not suitable.

Roller

For small areas only. Use short pile roller. Multiple coats may be re required.

Cleaner

International GTA220

Work Stoppages and Cleanup

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA220. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Clean all equipment immediately after use with International GTA220. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.

Welding

In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."

SAFETY

All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.

Limitations

This product will not cure adequately below 5°C. For maximum performance ambient curing temperatures should be above 10°C. In common with all epoxy based coatings Intershield 852 will exhibit chalking of the film on UV exposure. Rate of chalking will depend upon climatic conditions. Except in hot countries, chalking will be limited to a thin surface layer. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating. In the overcoating data section 'ext' = extended overcoating period. Please refer to our Marine Painting Guide - Definitions and Abbreviations available on our website.

Unit size

Unit size Part A Part B
  Vol Pack Vol Pack
20 lt 16.5 lt 20 lt 3.5 lt 5 lt

Unit shipping weight

Unit size Unit Weight
20 lt 40.94 Kg

Storage

Shelf Life 12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.
Яндекс.Метрика