A one pack alkyd gloss finish.
For use as an easily maintained cosmetic finish coat on areas above the waterline. For use at Newbuilding, Maintenance & Repair or On Board Maintenance.
|color||CLB000-White, CLD260-Intl. Orange, CLK724-Storm Grey, CLL274-Red, CLL549-Signal Green, CLY999-Black ; and a wide range of colours.|
|Part B (Curing Agent)||Not applicable|
|Volume Solids||48% ±3% (ISO 3233:1998)|
|Typical Film Thickness||40 microns dry (83 microns wet)|
|Theoretical Coverage||12.00 m2/litre at 40 microns dft, allow appropriate loss factors|
|Method of Application||Airless Spray, Brush, Conventional Spray, Roller|
|Flash Point||Single Pack 40°C (Product produced and supplied in North America has a flashpoint of 41°C due to locally sourced solvents. There is no detrimental effect on product performance.)|
|Touch Dry [ISO 1517:73]||16 hrs||14 hrs||6 hrs||5 hrs|
|Hard Dry [ISO 9117:90]||62 hrs||48 hrs||24 hrs||12 hrs|
|Overcoated By||Substrate Temperature|
|Interlac 665||36 hrs||ext||24 hrs||ext||24 hrs||et||16 hrs||ext|
420 g/lt as supplied (EPA Method 24) 364 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)
VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
When used as part of an approved scheme, this material has the following Certification:
- Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16))
- Fire Resistance - Surface Spread of Flame (Korean Register of Shipping)
- Fire Resistance - MSC61(67) Smoke & Toxicity (WFR)
- Fire Resistance - Marine Equipment Directive compliant
- Food Contact - Carriage of Grain (NOHA)
- Meets Petrobras Standard N-2492 - Alkyd Finish Gloss
Consult your International Paint representative for details.
System and compatibility
Interlac 665 should only be applied over recommended anticorrosive primers. The primer to be used will depend upon vessel area, existing coatings, coating condition and application location. Typical primers include:
- Interprime 198
- Intertuf 203
- Interprime 128 (in Europe)
- Interprime 222 (in South America)
- Interprime 234 (in North America)
- Interprime 538 (in Europe)
- Interlac 497 (applied as a sympathetically coloured undercoat over Interprime 198)
In the Americas, Interlac 665 may also be applied over epoxy primers or epoxy tie coats. Consult International Paint. Consult your International Paint representative for the system best suited for the surfaces to be protected.
Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
Interlac 665 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Interlac 665 must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa21⁄2 (ISO 8501-1:2007) and primed prior to the application of Interlac 665
Repair corroded areas with an appropriate International Paint primer (consult the primer data sheet).
Interlac 665 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Interlac 665 must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa21⁄2 (ISO 8501-1:2007) and primed prior to the application of Interlac 665 Interlac 665 may be applied directly over aged Interlac 665 following thorough fresh water washing and degreasing provided the coating to be overcoated is in an intact and tightly adherent condition. Loose or flaking coatings should be removed back to a firm edge and Interlac 665 or an appropriate primer should be used to repair the area before application of the full coat. Consult your International Paint representative for specific recommendations.
This material is a one pack coating and should always be mixed thoroughly with a power agitator before application.
Not recommended. Use International GTA004 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation.
Recommended Tip Range 0.33-0.48 mm (13-19 thou) Total output fluid pressure at spray tip not less than 141 kg/cm2 (2010 p.s.i.)
Use suitable proprietary equipment. Thinning may be required.
Work Stoppages and Cleanup
Thoroughly flush all equipment with International GTA004. All unused material should be stored in tightly closed containers. Partially filled containers may show surface skinning and/or a viscosity increase of the material after Storage. Material should be filtered prior to use.
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."
All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.
Interlac 665 is not suitable for use on immersed areas. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected Storage in accordance with information given in the Storage Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating. In the overcoating data section 'ext' = extended overcoating period. Please refer to our Marine Painting Guide - Definitions and Abbreviations available on our website.
|20 lt||20 lt||20 lt|
|5 lt||5 lt||5 lt|
|5 US gal||5 US gal||5 US gal|
|1 US gal||1 US gal||5 US gal|
Unit shipping weight
|Unit size||Unit Weight|
|20 lt||23.9 Kg|
|5 lt||6.01 Kg|
|5 US gal||49.5 lb|
|1 US gal||10 lb|
|Shelf Life||24 months minimum at 25°C. Subject to reinspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition|