eng Русский язык

Intergard 410

A two pack, high build epoxy intermediate or finish coat with good chemical and abrasion resistance.

Intended uses

For use on above water areas and in dry cargo holds as a high build intermediate or finish coat on structural steel, piping etc. For use at Newbuilding, Maintenance & Repair or On Board Maintenance.

color EMB000-White ; and a wide range of colours.
Finish/Sheen Gloss
Part B (Curing Agent) EMA080
Volume Solids 60% ±2% (ISO 3233:1998)
Mix Ratio 4 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness 125 microns dry (208 microns wet)
Theoretical Coverage 4.80 m2/litre at 125 microns dft, allow appropriate loss factors
Method of Application Airless Spray, Brush, Conventional Spray, Roller
Flash Point Part A 30°C; Part B 29°C; Mixed 30°C
Induction Period Not required

Drying Information

  Substrate Temperature
  10°C 15°C 25°C 35°C
Touch Dry [ISO 9117/3:2010] 5 hrs 4 hrs 2 hrs 60 hrs
Hard Dry [ISO 9117-1:2009] 24 hrs 20 hrs 10 hrs 6 hrs
Pot Life

8 hrs

6 hrs 4 hrs 2 hrs

Overcoating Data

Overcoated By Substrate Temperature
  5°C 10°C 25°C 35°C
  Min Max Min Max Min Max Min Max
Intergard 410 24 hrs 10 days 20 hrs 7 days 10 hrs 7 days 6 hrs 4 days
Interthane 990 24 hrs 10 days 20 hrs 7 days 10 hrs 7 days 6 hrs 4 days

Regulatory data


403 g/lt as supplied (EPA Method 24) 338 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)


VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.


When used as part of an approved scheme, this material has the following Certification:

  • Food Contact - Carriage of Grain (NOHA)
  • Fire Resistance - Marine Equipment Directive compliant
  • Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16))

Consult your International Paint representative for details.

System and compatibility

Consult your International Paint representative for the system best suited for the surfaces to be protected.

Surface preparations

Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.


Intergard 410 should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intergard 410 must be applied within the overcoating intervals specified (consult the relevant product data sheet).Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa21⁄2 (ISO 8501-1:2007) and primed prior to the application of Intergard 410


Repair corroded areas with the specified anticorrosive scheme and apply Intergard 410 within the overcoating intervals specified for the primer (consult relevant primer data sheet). Apply the Intergard 410 within the overcoating interval specified for the primer, (consult relevant primer data sheet). Ensure that the area is clean and dry prior to application of Intergard 410. Consult your International Paint representative for specific recommendations.



Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.


Not Recommended. Use International GTA220 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Recommended Tip Range 0.45-0.58 mm (18-23 thou) Total output fluid pressure at spray tip not less than 176 kg/cm2 (2500 p.s.i.)

Conventional Spray

Suitable. Use suitable proprietary equipment. Thinning may be required.


Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


Application by roller is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


International GTA822

Work Stoppages and Cleanup

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA822. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Clean all equipment immediately after use with International GTA822. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life Limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.


In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."


All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations. Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.


This product will not cure adequately below 5°C. For maximum performance ambient curing temperatures should be above 10°C. In common with all epoxy based coatings Intergard 410 will exhibit chalking of the film on UV exposure. Where a cosmetic finish with good gloss and colour retention is required, overcoat with recommended top coats. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected Storage in accordance with information given in the Storage Section of this data sheet. Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.

Unit size

Unit size Part A Part B
  Vol Pack Vol Pack
20 lt 16 lt 20 lt 4 lt 5 lt

Unit shipping weight

Unit size Unit Weight
20 lt 28.4 Kg


Shelf Life 12 months minimum at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.