eng Русский язык

Interbond 808

A light coloured, tar free, surface tolerant, two pack epoxy coating with high volume solids (82%). Interbond 808 is capable of being applied as a one or two coat system over grit blasted, hydroblasted or mechanically cleaned surfaces. It is also tolerant of damp surfaces (see limitations section).


A high performance epoxy coating for use in water ballast tanks, cofferdams, void spaces, wet spaces, bilges and crude oil tanks.
For use at Maintenance & Repair or On Board Maintenance.


KRA850-Buff, KRA853-Aluminium
KRA854-White (available in Brazil only)
KRA859-Black (available in USA only)

Finish/Sheen Not applicable
Part B (Curing Agent) KRA855
Volume Solids 82% ±2% (ISO 3233:1998)
Mix Ratio 4 volume(s) Part A to 1 volume(s) Part B
Typical Film Thickness

300 microns dry (366 microns wet)

Theoretical Coverage

2.73 m2/litre at 300 microns dft, allow appropriate loss factors

Method of Application Airless Spray, Brush, Roller
Flash Point

Part A 32°C; Part B 58°C; Mixed 33°C

Induction Period Not required

Drying Information

  Substrate Temperature
  5°C 15°C 25°C 35°C
Touch Dry [ISO 9117/3:2010] 15 hrs 8 hrs 3.5 hrs 2 hrs
Hard Dry [ISO 9117-1:2009] 34 hrs 18 hrs 7 hrs 4 hrs
Walk-on Time
44 hrs 21 hrs 7 hrs 5 hrs
Before Flooding 3 days 2 days 24 hrs 12 hrs
Pot Life 2 hrs 100 mins 75 mins 30 mins

Overcoating Data

see limitations

Overcoated By Substrate Temperature
15°C 25°C 35°C
  Min Max Min Max Min Max Min Max
Interbond 808 48 hrs 14 days 30 hrs 10 days 12 hrs 7 days 8 hrs 5 days


VOC 220 g/lt as supplied (EPA Method 24)
152 g/kg of liquid paint as supplied. EU Solvent Emissions Directive
(Council Directive 1999/13/EC)


VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.



When used as part of an approved scheme, this product has the following certification:
• Tank Coatings - B1 Classification of Ballast Tank Coatings (DNV/Marintek tested)

Consult your International Paint representative for details.


Consult your International Paint representative for the system best suited for the surfaces to be protected.


Paint only clean surfaces. Remove all grease, oil, soluble contaminants and other foreign matter by "solvent cleaning" (SSPC-SP1).


Abrasive blast clean to Sa2 (ISO 8501:1:1988) or hydroblast to International Paint hydroblasting standard HB2M/H (If abrasive blasting, the area should be fresh water washed prior to commencement).


Prepare areas of corrosion by mechanical cleaning to St3 (ISO 8501-1) or hydroblast to International Paint Standard HB2M/H. Abrade surrounding intact area and feather the edges. If overcoating large areas of aged two component coatings, the surfaces should be high pressure fresh water washed prior to application. Consult your International Paint representative for specific recommendations regarding two component coatings suitable for overcoating with Interbond 808. Interbond 808 should not be used to maintain or overcoat one component ballast coatings.
When applying Interbond 808 as a two coat scheme, Interbond 808 Aluminium must always be applied as the first coat.



Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified.
(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.


Not recommended. Use International GTA220 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation.

Airless Spray

Tip Range 0.45-0.66 mm (18-26 thou)
Total output fluid pressure at spray tip not less than 190 - 246 kg/cm2 (2700 - 3500 p.s.i.) Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified


Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.


Not recommended.


International GTA822/GTA220

Work Stoppages and Cleanup

Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA822/GTA220. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.
Clean all equipment immediately after use with International GTA822/GTA220. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.


In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."


All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.

Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.



This product will not cure adequately below 5°C. Substrate temperature should not exceed 40°C.
Interbond 808 can be applied over a damp but drying surface - not a wet surface. It cannot be applied over pools of water or water droplets. A simple test for dampness is as follows: With a finger, mark a 'V' on the surface to be coated. If drops of water collect at the bottom of the 'V', then the surface is wet not damp and should not be coated. The surface may be dried however and coated provided that it does not become wet during application.
Interbond 808 series is capable of continuing its cure process once immersed in water. However, early immersion following application will tend to retard coating cure and may result in soft films. See 'Drying Times, before flooding'. The curing agent for Interbond 808 has a tendency to go cloudy when stored at temperatures below 5°C. Warming the curing agent above 5°C will restore the clear nature of the product. No adverse effect on performance is observed if the curing agent is cloudy when used.
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. For optimum application properties bring the material to 25-30°C, unless specifically instructed otherwise, prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance with information given in the STORAGE Section of this data sheet.
Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.


Unit Size Part A Part B
  Vol Pack Vol Pack
20 lt 16 lt 20 lt 4 lt 5 lt
5 US gal 4 US gal 5 US gal 1 US gal 1 US gal
1 US gal 0.8 US gal 1 US gal 0.2 US gal 1 US gal

For availability of other unit sizes consult International Paint


Unit Size Unit Weight
20 lt 34.7 Kg
5 US gal 86.7 lb
1 US gal 18 lb


Shelf Life

12 months at 25°C. Subject to re-inspection thereafter. Store in dry, shaded conditions away from sources of heat and ignition.